Description
Requires Crestron Home OS 4.12 or later.
TESTERS WANTED
This extension has not yet been tried on a Pentair IntelliCenter: it is built to the protocol and checked in the CPLLC lab without the hardware. If you have a Pentair IntelliCenter on a Crestron Home system and can try it, please contact us. The two-hour trial is enough to tell whether it works, and your report decides what gets fixed first.
The CPLLC Pentair IntelliCenter extension brings a Pentair IntelliCenter pool and spa control system into Crestron Home as a tile with a page of its own. The page has a switch for each pool’s and spa’s filter pump, each light, light show and feature, each heater’s setpoint and heat mode, the color or show of IntelliBrite, MagicStream and GloBrite lights and the IntelliChlor’s output, and the water and air temperatures, pumps, IntelliChlor and IntelliChem readings below them. Every control has its sequence actions and events. It talks to the IntelliCenter directly on the home network, and the IntelliCenter reports every change as it happens, so the page follows the pool equipment at once, whether it was changed from Crestron Home, the IntelliCenter panel, the Pentair Home app or a schedule.
Drivers->Pool Controller->Pentair->IntelliCenter (Latest Release Notes) (Download Latest Version)
Windows utility that simplifies sideloading of drivers and extensions.
The extension’s own license key, or a CPLLC site license key, is entered in the extension’s Enter License Key option. The License Manager is not required, but it is the convenient place to enter a site license key once for every CPLLC driver.
All license purchases are final and non-refundable. Every CPLLC driver works fully for two hours without a key: test it on your processor before you buy. See the Terms of Use.
Installer Options
- IP Address / Hostname – The IntelliCenter’s address. Leave blank to find it on the processor’s network (the same subnet only).
- Port – 6681, the IntelliCenter’s own port. Change it only if the IntelliCenter is reached through another port.
- Obtain License Key – Opens CPLLC.net, where license keys and site licenses can be purchased.
- Enter License Key – The Pentair IntelliCenter license key. Leave blank when the site has a CPLLC site license.
- Show on Home Screen – Shows the tile on the Home screen (default off).
- Show in Room Screen – Shows the tile in its room (default on).
- Only Display Tile – Shows the tile alone, with no page of controls (default off).
- Starting Pin Code – A numeric PIN that must be entered before the page opens. Blank means no PIN (the default).
- Seconds Pin Active – How long the page stays unlocked after the last touch (default 10 seconds).
Actions
- Pool Filter On / Pool Filter Off – Turns a pool or spa on or off (its circulation); the same for each light, light show and feature (Spa Light On, Waterfall Off …).
- Set Pool Heater Setpoint °F – A body’s heat setpoint, in the system’s own scale.
- Set Pool Heater Heat Mode – A body’s heat mode, from the modes its heaters allow (Off, Heater, Solar Only …).
- Set Pool Light Effect – The color or show of an IntelliBrite, MagicStream or GloBrite light.
- Set IntelliChlor Output % – The chlorinator’s output, 0 to 100 %.
- Extension Enable / Extension Disable – Enables or disables the device. A disabled device shows Disabled, ignores its controls and raises no events.
Events
- Pool Filter On / Pool Filter Off – A body, light, light show or feature turned on or off.
- Pool Heater Heat Mode is <mode> – A body’s heat mode changed.
- Pool Light Effect is <color or show> – A light’s color or show changed.
- Pool Offline / Pool Online – The IntelliCenter can’t be reached; it can again.
- Extension Enabled / Extension Disabled – The device was enabled or disabled.
- Pin Locked / Pin UnLocked – The PIN keypad locked again, or the right PIN was entered (with a Starting Pin Code set).
- Extension Is Enabled Changed – Crestron Home’s own event for each of the states a sequence can test, raised whenever that state changes.
States
- Extension Is Enabled – True while the extension is enabled, False while it is disabled.
Pentair, IntelliCenter, IntelliBrite, IntelliChlor, IntelliChem, MagicStream, GloBrite, UltraTemp, MasterTemp and Max-E-Therm are trademarks of their respective owners. Crestron and Crestron Home are trademarks of Crestron Electronics, Inc. This extension is an independent product of Control Programming LLC and is not affiliated with, endorsed by or sponsored by the owners of Pentair, IntelliCenter, IntelliBrite, IntelliChlor, IntelliChem, MagicStream, GloBrite, UltraTemp, MasterTemp and Max-E-Therm.


